Stunning Sterling Silver Rectangle Wire, Pearl, and Chain Earrings (jewelry tutorial)


Products NEEDED
6 one l/i" head pins
2" four x 1 mm sterling silver rectangle wire Two one' pieces of sterling silver chain Two pearl beads
Two one.4 mm spherical sterling silver beads Two sterling silver ear wires
TOOLS Essential
Ruler
Marker
Jeweler's saw or tin snips Basic safety Eyeglasses Tough, flat area Awl
Hammer /Ίί" drill bit
Handheld rotary Software, flex shaft, or drill press File
High-quality grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Round nose pliers


one.Use the ruler to measure and mark two Γ parts of 4 x one mm rectangle sterling silver wire.
2.Utilizing a jeweler's saw or tin snips, Minimize the 4 x 1 mm rectangle sterling silver wire into two Γ lengths.
three.File Each and every conclusion from the one" rectangle wire pieces to get rid of any burs or tough edges; You can utilize the file to around the ends on the rectangle wire parts If you'd like. Utilize a good grit sanding pad to go in excess of the area where you have submitted to smooth the perimeters and take away any file marks.
4.Make use of the ruler to evaluate and mark '/*’ from Every conclusion of the Γ items of rectangle wire and position a mark in the center in the wire. This tends to be where you drill the holes to slip The pinnacle pins via.
5Next, place on the security Eyeglasses! Then put the Γ rectangle wire pieces on to a tough, flat surface. Spot The purpose of the awl within the mark that you choose to produced /(." from Every single close from the rectangle wire items, and utilize a hammer to firmly strike once on the very best with the awl. This could make a pilot hole for drilling holes to the rectangle wire.


six.Using a drill bit. drill holes into Every single close of the rectangle wire items that has a handheld rotary Software, flex shaft, or drill press (even though continue to wearing your security Eyeglasses!).
seven.Use the file or fantastic grit sanding pad to remove any burs or tough edges left from drilling holes in to the rectangle wire items.

eight.Curve both Γ pieces of rectangle wire into a form employing a ring mandrel and rawhide mallet. If you don't have a ring mandrel and rawhide mallet, use two pairs of chain nose pliers. Holding one particular pair in Each individual hand, grasp each stop on the Γ rectangle wire piece from the chain nose pliers and Carefully bend the rectangle wire into a “C shape, aligning the holes which you drilled on Just about every close of the Γ rectangle wire pieces. Examine equally of your C-formed rectangle wire pieces and modify the curves so that they are related in dimensions.

Established these men's gold & silver rings apart.
9.Use the ruler to measure the chain into Γ items. Make use of the wire cutters to chop the chain, and established these parts apart.



ten.Place a head pin through a pearl bead after which incorporate just one one.four mm sterling silver bead.
eleven.Use the ruler to measure and mark /t" over the very best bead on The top buy men's rings pin. With wire cutters or tin snips, Minimize The top pin wire Yu," earlier mentioned the best bead.
twelve.Utilizing the chain nose pliers, bend The pinnacle pin wire next to the top bead at a 90-degree angle.
13.Hold The top pin mens casual rings Together with the pearl bead along with the silver bead on it in a single hand Along with the wire that you bent pointing towards you. Utilizing the spherical nose pliers, grip the top of The pinnacle pin wire that may be pointing towards you and roll it clear of you (think of turning the ignition key to start your car). Release the pliers from The pinnacle pin wire. At this stage, the opening in the loop at the best of The pinnacle pin wire need to be large enough to slide the Γ duration of chain on it right before closing the loop of The pinnacle pin. When you increase the chain, utilize the spherical nose pliers to grasp the loop of The top pin wire and roll it shut. You need to use the round nose or chain nose pliers to adjust the shape from the loop at the top of the head pin if you need to.


fourteen.Repeat this move on the 2nd pearl and silver bead. Established these apart.
15.Spot a head pin with the hole drilled into 1 end of the rectangle wire “C* shape with The underside or flat conclusion on The within curve on the rectangle wire *C* form. Make use of the ruler to measure and mark the head pin s/u.m above the rectangle wire. With wire cutters or tin snips, Slash The pinnacle pin wire earlier mentioned the highest in the rectangle wire.
16.Use the chain nose pliers to bend the head pin wire beside the rectangle wire in a 90-degree angle.
17.With the chain nose pliers in a single hand, keep The underside or flat location of the head pin firmly against the rectangle wire with The pinnacle men's designer rings & wedding bands pin wire that you choose to bent pointing towards you.
Using your other hand, make use of the round nose pliers to grip the top of The pinnacle pin wire and roll it faraway from you. Release the head pin wire. At this point, the opening during the loop of The top pin wire need to nevertheless be big enough to slide the tip website link from the 1' chain on to iL Now incorporate the chain for the loop of the head pin. after which you can utilize the round nose pliers to grasp the loop of the head pin wire and roll it shut. You may use the spherical nose or chain nose pliers to adjust the shape from the loop at the top of The pinnacle pin.

eighteen.Repeat this method on another gap from the C-shaped rectangle wire. Rather than adding the one * size of chain With all the pearl and also the sterling silver bead, increase the ear wire at the opposite conclude. Slip the ear wire onto the men's designer rings & wedding bands loop of The pinnacle pin just before closing the loop.
19.Repeat the preceding methods on the next earring.

 

Pleasing Sterling Silver Rectangle Wire, Pearl, and Chain Earrings (jewelry tutorial)


Resources Essential
Six one l/i" head pins
2" four x 1 mm sterling silver rectangle wire Two one' parts of sterling silver chain Two pearl beads
Two 1.four mm round sterling silver beads Two sterling silver ear wires
Applications Required
Ruler
Marker
Jeweler's observed or tin snips Safety Eyeglasses Difficult, flat floor Awl
Hammer /Ίί" drill bit
Handheld rotary Device, flex shaft, or drill press File
Wonderful grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Spherical nose pliers


1.Utilize the ruler to measure and mark two Γ items of 4 x 1 mm rectangle sterling silver wire.
two.Using a jeweler's noticed or tin snips, cut the 4 x one mm rectangle sterling silver wire into two Γ lengths.
3.File Each individual finish with the 1" rectangle wire items to remove any burs or rough edges; You may use the file to round the finishes of the rectangle wire items If you prefer. Make use of a great grit sanding pad to go more than the world where you have filed to sleek the edges and take away any file marks.
4.Make use of the ruler to evaluate and mark '/*’ from Every conclude of the Γ items of rectangle wire and position a mark in the center on the wire. This will be where you drill the holes to slip The pinnacle pins by means of.
5Next, set in your basic safety Eyeglasses! Then spot the Γ rectangle wire items on to a hard, flat floor. Put the point on the awl on the mark which you designed /(." from each stop with the rectangle wire pieces, and use a hammer to firmly strike the moment on the best from the awl. This is likely to make a pilot gap for drilling holes into the rectangle wire.


6.Utilizing a drill little bit. drill holes into Every conclude of the rectangle wire pieces that has a handheld rotary Software, flex shaft, or drill press (although however wearing your security glasses!).
seven.Utilize the file or good grit sanding pad to eradicate any burs or tough edges remaining from drilling holes into the rectangle wire items.

eight.Curve both equally Γ pieces of rectangle wire into a form utilizing a ring mandrel and rawhide mallet. If you don't have a hoop mandrel and rawhide mallet, use two pairs of chain nose pliers. Holding a single pair in Every single hand, grasp Each individual end in the Γ rectangle wire piece while in the chain nose pliers and Carefully bend the rectangle wire right into a “C shape, aligning the holes that you simply drilled on Every single conclusion of your Γ rectangle wire pieces. Examine equally with the C-formed rectangle wire parts and adjust the curves so that they are equivalent in dimensions.

Established these apart.
9.Use the ruler to measure the chain into Γ items. Make use of the wire cutters to chop the chain, and established these parts apart.



10.Location a head pin by way of a pearl bead then insert a person one.4 mm sterling silver bead.
11.Use the ruler to measure and mark /t" previously mentioned the highest bead on The top pin. With wire cutters or tin snips, Slice The pinnacle pin wire Yu," above the top bead.
12.Using the chain nose pliers, bend The top pin men's rings wire close to the highest bead in a ninety-diploma angle.
thirteen.Keep The pinnacle pin with the pearl bead and also the silver bead on it in one hand With all the wire that you just bent pointing towards you. men's college ring Utilizing the spherical nose pliers, grip the tip of The pinnacle pin wire that is definitely pointing towards you and roll it clear of you (visualize turning the ignition key to start your car). Release the pliers from mens casual rings the head pin wire. At this point, the opening within the loop at the top of the head pin wire ought to be big adequate to slip the Γ length of chain on it just before closing the silver rings for men loop of the head pin. After you include the chain, use the round nose pliers to grasp the loop of the head pin wire and roll it closed. You should use the round nose or chain nose pliers to adjust the shape of your loop at the best of The pinnacle pin if you might want to.


fourteen.Repeat this move on the 2nd pearl and silver bead. Established these apart.
fifteen.Area a head pin throughout the hole drilled into a single stop from the rectangle wire “C* shape with the bottom or flat end on the inside curve of your rectangle wire *C* condition. Utilize the ruler to evaluate and mark The pinnacle pin s/u.m earlier mentioned the rectangle wire. With wire cutters or tin snips, Minimize The top pin wire previously mentioned the very best from the rectangle wire.
16.Utilize the chain nose pliers to bend The pinnacle pin wire beside the rectangle wire in a 90-degree angle.
17.With the chain nose pliers in a single hand, keep The underside or flat spot of The top pin firmly in opposition to the rectangle wire with the head pin wire that you simply bent pointing toward you.
With your other hand, use the spherical nose pliers to grip the top of The top pin wire and roll it from you. Release the head pin wire. At this stage, the opening from the loop of The top pin wire must nonetheless be big enough to slide the top url in the 1' chain onto iL Now increase the chain to your loop of The top pin. after which use the spherical nose pliers to grasp the loop of The pinnacle pin wire and roll it closed. You should use the round nose or chain nose pliers to regulate The form in the loop at the top of men's rings The pinnacle pin.

eighteen.Repeat this process on the other gap while in the C-shaped rectangle wire. Rather than adding the one * size of chain Using the pearl and the sterling silver bead, increase the ear wire at the opposite stop. Slip the ear wire onto the loop of The pinnacle pin ahead of closing the loop.
19.Repeat the preceding steps on the 2nd earring.

 

Fine Sterling Silver Rectangle Wire, Pearl, and Chain Earrings (jewelry tutorial)


Components Essential
Six one l/i" head pins
two" 4 x one mm sterling silver rectangle wire Two 1' parts of sterling silver chain Two pearl beads
Two 1.four mm round sterling silver beads Two sterling silver ear wires
Equipment NEEDED
Ruler
Marker
Jeweler's noticed or tin snips Protection glasses Tricky, flat surface area Awl
Hammer /Ίί" drill little bit
Handheld rotary Instrument, flex shaft, or drill push File
Good grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Spherical nose pliers


1.Make use of the ruler to evaluate and mark two Γ items of four x 1 mm rectangle sterling silver wire.
two.Using a jeweler's noticed or tin snips, Slash the 4 x one mm rectangle sterling silver wire into two Γ lengths.
3.File Just about every end on the 1" rectangle wire items to eliminate any burs or rough edges; You should utilize the file to round the ends of your rectangle wire pieces In order for you. Use a fantastic grit sanding pad to go around the realm in which you have submitted to easy the sides and remove any file marks.
4.Utilize the ruler to measure and mark '/*’ from Each and every close from the Γ items of rectangle wire and place a mark in the center with the wire. This may be in which you drill the holes to slip the head pins by means of.
5Next, set on your basic safety Eyeglasses! Then location the Γ rectangle wire items on to a hard, flat surface area. Position the point in the awl to the mark that you created /(." from Just about every end in the rectangle wire parts, and use a hammer to firmly strike as soon as on the highest of your awl. This will make a pilot hole for drilling holes in the rectangle wire.


6.Using a drill bit. drill holes into Each individual finish on the rectangle wire parts with a handheld rotary Instrument, flex shaft, or drill push (though nonetheless donning your basic safety Eyeglasses!).
7.Make use of the file or wonderful grit sanding pad to reduce any burs or rough edges still left from drilling holes to the rectangle wire parts.

eight.Curve each Γ items of rectangle wire right into a condition employing a ring mandrel and rawhide mallet. If you do not have a ring mandrel and rawhide mallet, use two pairs of chain nose pliers. Keeping just one pair in each hand, grasp Every conclude with the Γ rectangle wire piece during the chain nose pliers and gently bend the rectangle wire into a “C form, aligning the holes you drilled on Each individual end from the Γ rectangle wire items. Assess both equally of the C-shaped rectangle wire pieces and alter the curves so that they're very similar in sizing.

Set these aside.
9.Use the ruler to measure the chain into Γ items. Make use of the wire cutters to chop the chain, and established these parts aside.



10.Location a head pin by way of a pearl bead then insert just one one.four mm sterling silver bead.
11.Use the ruler to measure and mark /t" over the very best bead on The top pin. With wire cutters or tin snips, Minimize The pinnacle pin wire Yu," higher than the best bead.
twelve.Using the chain nose pliers, bend the head pin wire next to the top bead at a 90-degree angle.
13.Maintain The top pin Along with the pearl bead as well as silver bead on it in a single hand While using the wire that you bent pointing toward you. Using the round nose pliers, grip the end of the head pin wire that is pointing toward you and roll it away from you (think of turning the ignition key to start your car). Release the pliers from the head pin wire. At this stage, the opening in the loop at the best of The pinnacle pin wire need to be significant enough to rings for men slide the Γ duration of chain on it right before closing the loop of The pinnacle pin. When you insert the chain, utilize the spherical nose pliers to grasp the loop of The top pin wire and roll it closed. You can utilize the round nose or chain nose pliers to adjust the shape of the loop at the top of the head pin if you might want to.


fourteen.Repeat this move on the 2nd pearl and silver bead. Established these apart.
15.Spot a head pin with the hole drilled into one end of the rectangle wire “C* condition with The underside or flat conclusion on The within curve in the rectangle wire *C* form. Use the ruler to measure and mark The pinnacle pin s/u.m higher than the rectangle wire. With wire cutters or tin men's designer rings & wedding bands snips, Slice The pinnacle pin wire previously mentioned the very best in the rectangle wire.
16.Use the chain nose pliers to bend The pinnacle pin wire beside the rectangle wire in a 90-degree angle.
seventeen.While using the chain nose pliers in a single hand, maintain the bottom or flat region of the head pin firmly versus the rectangle wire with men's gold & silver rings The pinnacle pin wire that you just bent pointing toward you.
Along with your other hand, use the spherical nose pliers to grip the top of The top pin wire and roll it far from you. Release The pinnacle pin wire. At this stage, the opening while in the loop of The top pin wire ought to still be men's rings personalized and engraved significant plenty of to slide the tip hyperlink of the one' chain on to iL Now include the chain to the loop of The pinnacle pin. then make use of the round nose pliers to grasp the loop buy men's rings of The pinnacle pin wire and roll it shut. You can utilize the round nose or chain nose pliers to regulate The form in the loop at the top of The pinnacle pin.

eighteen.Repeat this process on the other gap while in the C-shaped rectangle wire. Instead of introducing the 1 * length of chain While using the pearl plus the sterling silver bead, incorporate the ear wire at the other close. Slip the ear wire on to the loop of The top pin before closing the loop.
19.Repeat the previous methods on the second earring.

 

Delightful Sterling Silver Rectangle Wire and Seed Bead Earrings




Sterling Silver Crescent and Bead Earrings


Follow the step-by-phase Guidance to create these primary bead earrings using a loop closure.
Supplies Wanted
Two one' pieces of 4 x one mm sterling silver rectangle wire Two Vs" head pins forty seed beads (approximate quantity)
Two sterling silver ear wires
Equipment Desired
Ruler
Marker
Jeweler's saw or tin snips Security Eyeglasses Tricky, flat surface Awl
Hammer /ΐί’ drill bit
Hand-held rotary Software, flex shaft, or drill press File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Spherical nose pliers
one. Use the ruler to measure and mark two Γ items of four x one mm rectangle sterling silver wire.

2.Using a jeweler's noticed or tin snips, Slice the four x 1 mm rectangle sterling silver wire into two Γ lengths.
5. Place on your own safety glasses! Area the Γ rectangle wire parts on to a hard, flat surface area. Area The purpose of your awl around the mark which you designed /t" from Each individual finish in the rectangle wire, and firmly strike after on the best of your awl having a hammer. This can make a pilot hole for drilling holes in the rectangle wire.


three.File Each individual finish in the Γ rectangle wire items to get rid of any burs or tough edges. If wished-for, you can use the file to round the ends in the rectangle wire items. Make use of a high-quality grit sanding pad to go around the area where you have filed to easy the perimeters and take away any file marks.
four.Utilize the ruler to evaluate and mark '/is" from each finish in the Γ items of rectangle wire and area a mark in the middle of your wire. This will be where you will drill the holes to slide the head pins by means of.



Constantly don your basic safety Eyeglasses when accomplishing any position that might result in metal, stone, or any difficult materials flying close to. Safeguard your eyes from injuries continually!
If you do not have an awl, You should utilize a little nail to start out your pilot gap. Use the exact same system explained in this article for using an awl.



6.Using adrill bit. drill holes into each end of the rectangle wire pieces with a handheld rotary tool, flex shaft, or drill press (remember to have on your protection glasses!).
seven.Utilize the file or great grit sanding pad to eliminate any burs or tough edges remaining from drilling holes into your rectangle wire parts.
eight.Curve both equally Γ items on the rectangle wire into a *C form using a ring mandrel and rawhide mallet. Align the holes that you Σταυροι 18Κ Με Μπριγιαν simply drilled on Every finish of the 1" rectangle wire parts. Look at both equally with the C-formed rectangle wire items and alter the curves so that they are comparable in size.
If you don't have a hoop mandrel and rawhide mallet, use two pairs of chain nose pliers: Keeping one particular pair in Every Σταυροι single hand, grasp Each and every finish from the 1" rectangle wire piece in the chain nose pliers and Carefully bend the rectangle wire right into a “C form.




9.Slide the head pin through the holes during Βαπτιστικοι Σταυροι 18Κ Με Μπριγιαν the C-formed rectangle wire to ensure that the holes are vertically aligned and that the head pin slides through both of those holes conveniently. Accomplish these techniques for equally C-shaped rectangle wires.
10.Just after tests that The Σταυροι Με Διαμαντια top pins slide very easily through the holes during the C-formed rectangle wire, take away The top pins and set the *C" styles apart. Include two seed beads to the bottom of The pinnacle pin.
eleven.Slide The top pin Using the two seed
beads on it in the base hole from the C-formed rectangle wire.
twelve.Slide seed beads onto the head pin higher than The underside hole of the C-formed rectangle wire. (I utilised 11 seed beads, however , you can change the quantity of beads which you use. You might need to employ kind of beads with regards to the dimension of the beads made use of and the gap in between the holes over the C-formed rectangle wire.)
13.Slide The pinnacle pin from the best hole of your C-shaped rectangle wire.
14.Increase seed beads to The top pin above the best hole of the C-formed rectangle wire.
I employed 6 seed beads, but, yet again, you'll be able to adjust the quantity of beads you use. Just You should definitely depart a minimum of Yu." of head pin wire higher than the very best seed bead to allow plenty of wire to produce the loop closure.
fifteen.Make use of the ruler to measure and mark /t" earlier mentioned the very best bead on The pinnacle pin. Together with the wire cutters or tin snips, cut The pinnacle pin wire Yu’ over the best bead.
sixteen.Use the chain nose pliers to bend The top pin wire next to the highest bead at a ninety-degree angle.
seventeen.Maintain The pinnacle pin Together with the beads and the rectangle wire on it in a single hand Using the wire that you choose to bent pointing toward you. Utilizing the round nose pliers, grip the top of The top pin wire that may be pointing toward you and roll it away from you (your hand placement will be just like that of holding a bicycle handlebar). Launch the pliers from the head pin wire. At Βαπτιστικοι Σταυροι 18Κ Με Μπριγιαν this time, the opening from the loop at the highest of The pinnacle pin wire must however be huge more than enough to slip the ear wire on. Immediately after adding the ear wire, utilize the spherical nose pliers to grasp the loop of the head pin wire and roll it shut. If necessary, You should utilize the round nose or drain nose pliers to regulate the shape in the loop at the top of The top pin.
eighteen.Repeat these measures for the 2nd earring.

Nice Sterling Silver Rectangle Wire and Seed Bead Earrings




Sterling Silver Crescent and Bead Earrings


Follow the stage-by-action Directions to generate these standard bead earrings utilizing a loop closure.
Elements Required
Two 1' parts of 4 x 1 mm sterling silver rectangle wire Two Vs" head pins forty seed beads (approximate selection)
Two sterling silver ear wires
Resources NEEDED
Ruler
Marker
Jeweler's noticed or tin snips Basic safety Eyeglasses Difficult, flat floor Awl
Hammer /ΐί’ drill little bit
Hand held rotary Instrument, flex shaft, or drill push File
Great grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Round nose pliers
1. Make use of the ruler to evaluate and mark two Γ parts of 4 x 1 mm rectangle sterling silver wire.

two.Employing a jeweler's saw or tin snips, Lower the four x one mm rectangle sterling silver wire into two Γ lengths.
five. Put in your basic safety Eyeglasses! Place the Γ rectangle wire pieces onto a tough, flat area. Place the point on the awl to the mark that you created /t" from Every single close of the rectangle wire, and firmly strike as soon as on the very best of the awl using a hammer. This is likely to make a pilot gap for drilling holes into your rectangle wire.


3.File Every conclude with the Γ rectangle wire parts to eliminate any burs or rough edges. If preferred, You can utilize the file to around the finishes of your rectangle wire parts. Use a good grit sanding pad to go above the world in which you have submitted to sleek the sides and take away any file marks.
4.Use the ruler to measure and mark '/is" from Each and every conclude on the Γ parts of rectangle wire and put a mark in the middle of the wire. This may be where you will drill the holes to slide The top pins by means of.



Constantly don your protection Eyeglasses when accomplishing any job that might end in steel, stone, or any really hard product traveling all-around. Secure your eyes from injury at all times!
If you don't have an awl, You should use a small nail to start your pilot hole. Use exactly the same approach described right here for making use of an awl.



6.Making use of adrill bit. drill holes into Each and every stop in the rectangle wire pieces having a handheld rotary Instrument, flex shaft, or drill press (don't forget to put on your safety glasses!).
seven.Utilize the file or great grit sanding pad to reduce any burs or tough edges remaining from drilling holes in the rectangle wire items.
eight.Curve equally Γ items in the rectangle wire into a *C shape using a ring mandrel and rawhide mallet. Align the holes that you drilled on Each individual close of your 1" rectangle wire pieces. Compare both of the C-formed rectangle wire parts and change the curves so that they're related in measurement.
If you do not have a ring mandrel and rawhide mallet, use two pairs of chain nose pliers: Keeping a person pair in Just about every hand, grasp Just about every conclude on the 1" rectangle wire piece within the chain nose pliers and gently bend the rectangle wire right into a “C condition.




nine.Slide The top pin with the holes within the C-formed rectangle wire to be sure that the holes are vertically aligned Which The top pin slides via both holes conveniently. Accomplish these techniques for equally C-shaped rectangle wires.
10.Just after tests that The top pins slide very easily with the holes in the C-formed rectangle wire, take away The top pins and set the *C" styles apart. Incorporate two seed beads to the bottom of The pinnacle pin.
eleven.Slide The pinnacle pin Along with the two seed
beads on it throughout the bottom hole with the C-formed rectangle wire.
12.Slide seed beads onto The pinnacle pin previously mentioned the bottom gap with the C-shaped rectangle wire. (I utilized eleven seed beads, however, you can alter the amount of beads that you choose to use. You might require to utilize more or less beads depending on the dimensions on the beads utilized and the space involving the holes within the C-shaped rectangle wire.)
thirteen.Slide The top pin through the major hole from the C-formed rectangle wire.
14.Add seed beads to The pinnacle pin previously mentioned the top gap on the C-shaped rectangle wire.
I made use of 6 seed beads, but, once more, you could alter the amount of beads you utilize. Just Ensure that you leave no less than Yu." of head pin wire previously mentioned the top seed bead to permit adequate wire to generate the loop closure.
15.Utilize the ruler to evaluate and mark /t" Βαπτιστικοι Σταυροι Με Μπριγιαν above the best bead on The top pin. With the wire cutters or tin snips, Slice The top pin wire Yu’ higher than the highest bead.
16.Utilize the chain nose pliers to bend the head pin wire beside the very best bead at a ninety-degree angle.
seventeen.Hold The pinnacle pin Together with the beads and also the rectangle wire on it in a single hand With all the wire that you choose to bent pointing toward you. Utilizing the spherical nose pliers, grip the end of The pinnacle pin wire which is pointing towards you and roll it from you (your hand position might be much like that of Keeping a Σταυροι Βαπτισης bicycle handlebar). Release the pliers from The pinnacle pin wire. At this time, the opening during the loop at the very best of The pinnacle pin wire need to still be massive sufficient to slide the Σταυρος Με Μπριγιαν Τιμη ear wire on. Immediately after including the ear wire, utilize the round nose pliers to grasp the loop Σταυροι Με Διαμαντια of The pinnacle pin wire and roll it closed. If necessary, You need to use the round nose Σταυροι Βαπτισης or drain nose pliers to adjust The form in the loop at the best of The top pin.
eighteen.Repeat these measures for the 2nd earring.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15